Question 1

Where is the PUDU CC1 Pro used?

Accepted Answer

CC1 Pro is used in high-traffic commercial venues such as malls, airports, hotels, hospitals, and large open spaces. It is effective in 5000-8000 m² areas with VSLAM+ navigation requiring no QR codes.

Question 2

Can the PUDU CC1 Pro autonomously manage water and charging?

Accepted Answer

Yes. CC1 Pro's autonomous workstation automatically handles water filling/drainage when the level drops, auto-charges when the battery runs out, and completes the brush self-cleaning cycle.

Question 3

Where can I buy the PUDU CC1 Pro in Turkey?

Accepted Answer

PUDU CC1 Pro can be purchased in Turkey through Robotlar.org. Sales, rental, and technical support options are available for corporate projects.

Question 4

How does the CC1 Pro's Sweeping, Scrubbing, Carpet Vacuuming, and Silent Mopping function work?

Accepted Answer

The standard sweeping mode consists of a side brush, sweeping brushes, and a mopping-vacuuming unit with a dust cavity and mop. CC1 Pro performs sweeping, dust vacuuming, and dust mopping simultaneously. In scrubbing mode, water is distributed onto the scrubbing brushes to moisten the floor, and dirt is vacuumed into the recovery tank by the squeegee. In carpet vacuuming mode, sweeping brushes can be enabled or disabled; when disabled, the device runs in vacuum-only mode and the carpet nozzle deposits dust into the dust box.

Question 5

Under what circumstances does CC1 Pro automatically return to the Docking Station?

Accepted Answer

CC1 Pro automatically starts the refill/drainage process if its battery drops below 10%, fresh water falls below 5%, or the recovery tank becomes full. It also estimates the power needed to complete remaining tasks and recharges itself to that estimated level.

Question 6

Can CC1 Pro work fully autonomously without any manual intervention?

Accepted Answer

Yes. This is accomplished by using CC1 Pro together with a Docking Station (Workstation) and setting up scheduled tasks.

Question 7

What are the recommended maintenance and component replacement intervals for CC1 Pro?

Accepted Answer

Inspect the robot approximately every 2 days. Brushes, dust box, water filter box, scrubbing squeegee rubber strips, mopping-vacuuming mop, side brush, and filter cartridge should be replaced roughly every 3 months. Actual frequency may vary based on cleaning conditions and usage.

Question 8

How often is the cleaning report uploaded?

Accepted Answer

The cleaning report is uploaded immediately after task completion. If there is no internet connection, it is uploaded during the next software startup.

Question 9

How is the cleaning area and consumption calculated in the cleaning report?

Accepted Answer

The cleaning area is calculated by multiplying the cleaning path width (standard 500 mm) by the cleaning duration, excluding transition and pause time. Electricity consumption is the battery percentage difference before and after cleaning. Water consumption is tracked by a flow meter. The report may be divided into sections, with data from each section totaled for a comprehensive overview.

Question 10

How can I enable the assist mode?

Accepted Answer

On the home screen, tap the 'More' button, find the assist mode switch, then tap it to turn on assist mode.

Question 11

If the start time of task 2 is reached while task 1 is running, will the machine execute task 2?

Accepted Answer

No. At that point, task 2 will be considered null and will not be executed.

Question 12

How is the cleaning time calculated?

Accepted Answer

Cleaning time is calculated by measuring how long it takes to clean the designated area and path. Any pause time is not counted.

Question 13

How is the robot's starting position for a task determined?

Accepted Answer

For the zigzag path ('Arc' in software), the endpoint of the longer side of the outer path is chosen to maximize efficiency. For the spiral path ('Loop' in software), the endpoint of the outermost path is used as the starting position.

Question 14

How does CC1 Pro extricate itself from a difficult situation, and what is its maximum reverse distance?

Accepted Answer

When CC1 Pro enters a narrow space or encounters a blocking obstacle, it activates an extrication mechanism and moves left, right, or reverses until it finds a wider space, then continues its task. Rear sensors detect obstacles. The maximum continuous reverse distance is 30 cm.

Question 15

When is task re-planning triggered?

Accepted Answer

Task re-planning is triggered when CC1 Pro's path is completely blocked and it cannot proceed even after extrication attempts. The robot automatically generates a new path to a different cleaning area. The default stuck time limit is 30 seconds.

Question 16

How does the robot resume cleaning from where it left off after an interruption?

Accepted Answer

If the task is paused/canceled manually or the robot auto-returns due to low battery or water, it records the interrupted position. In the next operation, the robot navigates to that position and resumes cleaning from there.

Question 17

How much water does CC1 Pro use per hour or per square meter?

Accepted Answer

Assuming minimum 700 m²/hour efficiency, approximately 10 mL per square meter is used. Per hour: ~3,000 mL at low water speed, ~4,800 mL at medium, and ~7,200 mL at high water speed settings.

Question 18

Why does CC1 Pro return to the Charging Station after completing the task rather than when battery reaches 10%?

Accepted Answer

When battery drops to 10%, CC1 Pro typically starts returning to charge. However, during the final stage of scrubbing (water collection), it finishes that step first. During elevator use, gate passage, AGV traffic control zones, or water collection, charging is not initiated even below 10%. If estimated remaining task energy is below 10%, the robot continues; if battery drops below 5%, it is forced to return and recharge.

Question 19

What cleaning agent is recommended for CC1 Pro?

Accepted Answer

CC1 Pro's water supply system has been tested at pH6 and pH8; the recommended pH range is 6.5–7.5 (general: pH6–8). Avoid solutions containing limonene as it reacts with plastic components. Use a low-foaming or non-foaming solution, or add an anti-foaming agent. One recommended solution is 'Diversey'.

Question 20

When cleaning floors in medium soiled environments, what should you pay attention to?

Accepted Answer

Use a water filter box. Remove the air filter sponge and tightly cover the lid. Regularly wash the suction hose to prevent clogs. Set suction power to the highest level. Use mild cleaning agents that are non-acidic and non-alkaline.

Enterprise AI-Powered Autonomous Cleaning Guide

AI Spot Scrubbing (Local Cleaning)

PUDU VSLAM+ Navigation

AI Cleaning Performance Audit

Autonomous Workstation Series

Details & Performance Parameters.

Physical Architecture

Dynamic Performance

Energy & Protection

Computing & Intelligence

Let's Design the System.

CC1 Pro Frequently Asked Questions