Question 1

Where is PUDU CC1 used?

Accepted Answer

PUDU CC1 is designed for high-traffic environments such as shopping malls, hotel lobbies, airports, hospital corridors, office buildings, and large commercial spaces. It can operate automatically on both hard floors and carpet surfaces.

Question 2

What are PUDU CC1's 4-in-1 cleaning functions?

Accepted Answer

CC1 combines sweeping, scrubbing, vacuuming, and mopping in a single body. Its 17,000 Pa vacuum power effectively collects solid debris while the integrated moistening system polishes the floor surface — all applied in a single pass.

Question 3

How does the PUDU CC1 navigation system work?

Accepted Answer

CC1 operates on PUDU's proprietary SLAM positioning technology, combining visual SLAM and laser SLAM to build high-precision maps and plan autonomous paths around obstacles even in complex environments. Cleaning reports can be monitored in real time via the app integration.

Question 4

What are the PUDU CC1's battery life and water tank capacities?

Accepted Answer

CC1 offers up to 9 hours of continuous operation on a single charge. With a 15-litre clean water and 15-litre wastewater tank, it can complete large-area tasks without manual refilling. With optional auto-station support, charging, water filling, and drainage are also handled autonomously.

Question 5

Is PUDU CC1 available in Turkey?

Accepted Answer

Yes, PUDU CC1 is available in Turkey through Robotlar.org, including installation, map creation, task scheduling, and Turkish technical support. Use the Robotlar.org contact form to request a quote.

Question 6

How does CC1's Sweeping, Scrubbing, Carpet Vacuuming, and Silent Mopping function work?

Accepted Answer

The standard sweeping mode consists of a side brush, sweeping brushes, and a mopping-vacuuming unit with a dust cavity and mop. CC1 performs sweeping, dust vacuuming, and dust mopping simultaneously. In scrubbing mode, water is distributed onto the scrubbing brushes to moisten the floor, and dirt is vacuumed into the recovery tank by the squeegee. In carpet vacuuming mode, sweeping brushes can be enabled or disabled; when disabled, the device runs in vacuum-only mode and the carpet nozzle deposits dust into the dust box.

Question 7

Under what circumstances does CC1 automatically return to the Docking Station?

Accepted Answer

CC1 automatically starts the refill/drainage process if its battery drops below 10%, fresh water falls below 5%, or the recovery tank becomes full. It also estimates the power needed to complete remaining tasks and recharges itself to that estimated level.

Question 8

Can CC1 work fully autonomously without any manual intervention?

Accepted Answer

Yes. This is accomplished by using CC1 together with a Docking Station (Workstation) and setting up scheduled tasks.

Question 9

What are the recommended maintenance and component replacement intervals for CC1?

Accepted Answer

Inspect the robot approximately every 2 days. Brushes, dust box, water filter box, scrubbing squeegee rubber strips, mopping-vacuuming mop, side brush, and filter cartridge should be replaced roughly every 3 months. Actual frequency may vary based on cleaning conditions and usage.

Question 10

How often is the cleaning report uploaded?

Accepted Answer

The cleaning report is uploaded immediately after task completion. If there is no internet connection, it is uploaded during the next software startup.

Question 11

How is the cleaning area and consumption calculated in the cleaning report?

Accepted Answer

The cleaning area is calculated by multiplying the cleaning path width (standard 500 mm) by the cleaning duration, excluding transition and pause time. Electricity consumption is the battery percentage difference before and after cleaning. Water consumption is tracked by a flow meter. The report may be divided into sections, with data totaled for a comprehensive overview.

Question 12

How can I enable the assist mode?

Accepted Answer

On the home screen, tap the 'More' button, find the assist mode switch, then tap it to turn on assist mode.

Question 13

If the start time of task 2 is reached while task 1 is running, will the machine execute task 2?

Accepted Answer

No. At that point, task 2 will be considered null and will not be executed.

Question 14

How is the cleaning time calculated?

Accepted Answer

Cleaning time is calculated by measuring how long it takes to clean the designated area and path. Any pause time is not counted.

Question 15

How is the robot's starting position for a task determined?

Accepted Answer

For the zigzag path ('Arc' in software), the endpoint of the longer side of the outer path is chosen to maximize efficiency. For the spiral path ('Loop' in software), the endpoint of the outermost path is used as the starting position.

Question 16

How does CC1 extricate itself from a difficult situation, and what is its maximum reverse distance?

Accepted Answer

When CC1 enters a narrow space or encounters a blocking obstacle, it activates an extrication mechanism and moves left, right, or reverses until it finds a wider space, then continues its task. Rear sensors detect obstacles. The maximum continuous reverse distance is 30 cm.

Question 17

When is task re-planning triggered?

Accepted Answer

Task re-planning is triggered when CC1's path is completely blocked and it cannot proceed even after extrication attempts. The robot automatically generates a new path to a different cleaning area. The default stuck time limit is 30 seconds.

Question 18

How does the robot resume cleaning from where it left off after an interruption?

Accepted Answer

If the task is paused/canceled manually or the robot auto-returns due to low battery or water, it records the interrupted position. In the next operation, the robot navigates to that position and resumes cleaning from there.

Question 19

How much water does CC1 use per hour or per square meter?

Accepted Answer

Assuming minimum 700 m²/hour efficiency, approximately 10 mL per square meter is used. Per hour: ~3,000 mL at low water speed, ~4,800 mL at medium, and ~7,200 mL at high water speed settings.

Question 20

Why does CC1 return to the Charging Station after completing the task rather than when battery reaches 10%?

Accepted Answer

When battery drops to 10%, CC1 typically starts returning to charge. However, during the final stage of scrubbing (water collection), it finishes that step first. During elevator use, gate passage, AGV traffic control zones, or water collection, charging is not initiated even below 10%. If estimated remaining task energy is below 10%, the robot continues; if battery drops below 5%, it is forced to return and recharge.

Question 21

What cleaning agent is recommended for CC1?

Accepted Answer

CC1's water supply system has been tested at pH6 and pH8; the recommended pH range is 6.5–7.5 (general: pH6–8). Avoid solutions containing limonene as it reacts with plastic components. Use a low-foaming or non-foaming solution, or add an anti-foaming agent. One recommended solution is 'Diversey'.

Question 22

When cleaning floors in medium soiled environments, what should you pay attention to?

Accepted Answer

Use a water filter box. Remove the air filter sponge and tightly cover the lid. Regularly wash the suction hose to prevent clogs. Set suction power to the highest level. Use mild cleaning agents that are non-acidic and non-alkaline.

Question 23

What should be done about excessive noise from CC1?

Accepted Answer

In quiet environments such as malls and offices, noise levels may increase due to high suction power mode. Adjust suction and brush speed settings. Also, organize the cleaning sequence so that water collection during scrubbing is the final step, ideally performed in an unoccupied area.

Question 24

How can scrapes and scratches caused by CC1 be prevented?

Accepted Answer

A blind spot in the rear right area of CC1 can cause incidents during turns, and the algorithm does not include cleaning components in the obstacle avoidance range. Implement virtual walls or no-go zones in areas prone to scrapes and scratches.

Question 25

What should be done if water remains on the floor after cleaning?

Accepted Answer

Main causes: wide floor gaps, water on the scrubbing squeegee rubber strips, or water on the inner suction hose surface. Solutions: Regularly maintain the robot to prevent hose clogs that stop proper waste water vacuuming. Ensure no floor gaps in the water collection area; the robot will perform a back-and-forth motion to completely vacuum remaining waste water.

4-in-1 Versatile Cleaning Solution

4-in-1 Versatile Cleaning

17000 PA Superior Vacuum Power

Resume From Where It Left Off

PUDU SLAM Navigation Solution

Suitable for Various Floor Types

Automatic Water Filling and Drainage

Digital Cleaning and Reporting

Smart Elevator Control

Details & Performance Parameters.

Physical Architecture

Dynamic Performance

Energy & Protection

Computing & Intelligence

Let's Design the System.

PUDU CC1 Frequently Asked Questions